GRACO 132066

Shopping cart

Subtotal: $11.78

Checkout View Cart

Home
cart
Shop
  1. Home
  2. Simpson Strong-Tie
  3. Connectors

GRACO 132066

Sale!
0 customer reviews
View details

Current price is: $84.99. Original price was: $283.29.

Current price is: $84.99. Original price was: $283.29.

Add to cart
Buy Now
SKU: ETYAxfC9ozzwSBNK Categories:

Product Description

Simpson Strong-Tie HGLTV7.37/16 – Heavy Duty Hanger

The HGLTV is designed for structural composite lumber header (SCL) applications that require high loads. This heavy top-flange hanger features holes specifically located to prevent degradation of the header due to splitting of laminations. The Funnel Flange design allows for easy installation of beams.

Key Features

  • Versatile and heavy welded design allows for many modifications
  • Installs easily with Funnel Flange and with standard 16d common (0.162″ x 3 1/2″) nails
  • Can be welded to steel beam members

Finish

  • Simpson Strong-Tie gray paint. Hot-dip galvanized is available; specify HDG.

Installation

  • Use all specified fasteners. Verify that the header can take the required fasteners specified in the table.
  • For attaching to multi-ply headers, refer to technical bulletin Top-Flange Hanger Reductions for Multiple-Ply Headers (T-C-MPLYHEADR).
  • Flatten edge of header to match top-flange radius.
  • Bevel-cut the carried beam for skewed hangers.
  • For hangers exceeding the joist height by more than 1/2″, allowable load is 50% of the table load.
  • May be used for weld-on applications. Minimum required weld is a 1/4″ x 2 1/2″ fillet weld at each end of the top flange; see General Instructions for the Installer, note k, for weld information. Weld-on applications produce maximum loads listed. For uplift loads, refer to technical bulletin Top-Flange Hangers Welded to Structural Steel Members (T-C-WELDUPLFT).
  • May be installed on ledgers provided the ledgers are made of 4x solid sawn or 3 1/2″ SCL shown in the table below. Thinner ledgers must be evaluated by the building designer.

Options

  • Hot-dip galvanized; specify HDG.
  • Seats may be skewed to a maximum of 50 and/or sloped to a maximum of 45.
  • When seat is sloped, the maximum allowable load is 9,165 lb.
  • When seat is skewed, the maximum allowable load is 7,980 lb. The deflection at full loading may reach 1/4″. For skews greater than 15, multiply the table uplift load by 0.50.
  • For sloped and skewed seat combinations, the maximum allowable load is 7,695. The deflection at full loading may reach 1/4″. For skews greater than 15″, multiply the table uplift load by 0.50″.
  • Sloped or skewed seat hangers may not be installed in non-backed nailer/header installations.
  • Top flange may be sloped down to the left or right as far as 30. Reduce allowable loads using the following reduction factor based on linear interpolation (90)/90, where is the angle measure from the horizontal. This reduction is not cumulative with other load reductions.
  • Top flange may be offset left or right for placement at the end of a header. Minimum seat width is 3 1/4″. The maximum allowable load is 0.45. No uplift load is available.
  • For skewed and offset or skewed only top-flange hangers with inward or outward configuration, the maximum allowable load is the lesser of (a) 45% of the catalog load or (b) 4,300 lb.